It depends what you’re optimising for. If you want a single (relatively small) download to be available on your HDD as fast as possible, then your current setup might be better (optimising for lower latency). However, if you want to be maxing out your internet speeds at all time and increase your HDD speeds by making the copy sequential (optimising for throughput), then the setup with the catch drive will be better. Keep in mind that a HDD’s sequential write performance is significantly higher than its random write performance, so copying a large file in one go will be faster than copying a whole bunch of random chunks in a random order (like torrents do). You can check the difference for yourself by doing a disk benchmark and comparing the sequential vs random writes of your drive.

qBittorrent has exactly the option you’re looking for, I believe it’s called “incomplete download path” in the settings, letting you store incomplete downloads at a temporary path and moving them to their regular location when the download finishes. Aside from the download speed improvement, this will also lead to less fragmentation on your HDD (which might be part of the reason why it is so slow when downloading directly to it). Pre-allocating space could have the same effect, but I would recommend only using one of these two solutions at once (pre-allocating space on your SSD would only waste space)

It’s possible for a certain hardware/software setup not to support a certain codec. For example, my jellyfin client (Finamp) uses the iOS native decoders (afaik), which means opus files are practically broken. My music library (8000+ songs) contained exactly 1 lossy file, which just so happened to be an opus file. I decided to spend the extra ~20MB to standardise my entire library to flac files, ensuring I could play every song on all my devices.

Edit cause I posted too soon: you are generally correct; only in very specific circumstances will you encounter compatibility issues like this one in the modern world. This is 100% apple being apple, and you can expect pretty much every other (reasonably modern) device to support all codecs you might encounter in the wild.

To add to the audio compression: it isn’t possible to further compress an mp3 file without losing any quality. You can either:

1. Recompress to a lossy codec (mp3, aac, opus). This will lead to smaller file sizes if you set the bitrate lower than that of the input file, but it will always worsen the quality, no matter the bitrate.
2. Recompress to a lossless format (flac easily being the best one). Going from a lossy to a lossless format will increase the file size (sometimes by quite a substantial amount), while keeping the same quality. There is very little reason for you to do this
3. keep the original files (my recommendation)

If you’re willing to spend some extra time learning about audio compression, you can download lossless files and compress those directly to whatever format and bitrate you want. The quality will be better than option 1 above, as the audio is only lossely compressed once instead of twice.

“cis” and “trans” are prefixes denoting on what “side” something is. “cis” means “on this/our side”, while “trans” refers to “the other side”, for example:

1. “Cisalpina” is how the Romans referred to their side of the Alps (modern day Italy), while “Transalpina” referred to land on the other side of the alps.
2. There exist certain pairs of molecules with either a “cis” or “trans” prefix, depending on whether certain identical groups are on the same side or on opposite sides, respectively.

The modern use of “cis” and “trans” is generally about gender. A cisgender person is someone whose gender identity aligns with their sex assigned at birth, while a transgender person is someone for whom that doesn’t hold true.

In this meme, the person on the right is wearing a transgender flag for a shirt, and presumably offending the cisgender person on the left by calling them cis. The meme is making fun of the fact that some cisgender people consider “cis” an insult, when it really only is a neutral and non-offensive description.

YouTube would be smart enough not to advertise Adobe creative cloud in the pre-roll ads of this video, right? Right???

Which compression level are you using? My old server is able to compress flac’s at the highest (and therefore “slowest”) compression level at >50x speed, so bumping the level up shouldn’t be too hard on your CPU.

I’ve been running some external drives on my server for about a year now. In my experience, hard drives with an external power supply suffer less from random disconnects. The specific PC also makes quite a large difference in reliability. My server is just a regular desktop and has very little problem staying connected and powering my 3 external drives. My seedbox is an old laptop, and has been having almost constant problems with random disconnects and power issues. Maybe test how well your framework does with some external drives before committing to the plan?

Have you tried the official guide from the jellyfin website?

As for the guide this AI generated: it bothers me that they instruct you to use chocolatey for the *arrs, but still advice you to install docker, qbittorrent and jellyfin manually (all of which have chocolatey packages). I disagree with the comment that external storage would be recommended, as internal storage is generally more reliable (depending on a lot of factors of course). Also, I believe the “adding a library”-section of the jellyfin setup is a bit too short to be of any use, and would recommend referring to the jellyfin docs instead.

This guide also doesn’t explain how to make jellyfin accessible outside of your LAN. Once again, I’d recommend referring to the jellyfin docs if you want to do this.

I personally have only set up qbittorrent, jellyfin and docker (not the *arr suite), so I can’t comment on the completeness of the guide, but I wouldn’t trust it too much (seeing the previous oversights).

And finally, as someone who started their selfhosted server journey on windows: don’t. There is a reason why almost all guides are written for linux, as it is (in my humble opinion) vastly superior for server usage once you get used to it.

didn’t know that was a part of bisexuality

I should probably flee before I get eaten by an army of blahåjar (apparently that’s the correct plural?)

Oh I don’t mind the nitpicking, thanks for the explanation! I (apparently erroneously) thought “demake” and “decompile” were synonyms. Guess I’m one of today’s 10000.

In that case the (now taken down, but forked a gazillion times) portal64 project would be a correct example of a demake, right?

interested in females

Username checks out, though I’m assuming you meant “demakes”?

Anyways, the demake I’m most familiar with is the in-progress Lego island. The YouTuber behind it documented part of the process in vlogs (linked on the GitHub page), so that might be an interesting starting point.

I tried using Linux alternatives to iTunes, but it was always a pain. Even iTunes itself on a separate windows box was more of a hassle than I wanted. I eventually discovered rockbox, which works great with my iPod (5th gen AKA video): it has way more config options and allows me to simply create .m3u playlists and use my own folder structure. If your iPod is supported (https://www.rockbox.org/wiki/IpodPort.html), I’d absolutely recommend Rockbox over other solutions.

If your iPod isn’t supported by Rockbox (like my nano 5th gen), you could probably use strawberry or GTKpod. Both are imperfect, but work “good enough”.

Oh never mind, you’re already using the proprietary driver.

Which GPU do you use? I believe mint defaults to the nouveau drivers for Nvidia GPU’s, which generally has significantly worse performance compared to the proprietary driver.

You could look at the awesome-selfhosted list, specifically these two sections:

https://awesome-selfhosted.net/tags/recipe-management.html

https://awesome-selfhosted.net/tags/task-management--to-do-lists.html

I don’t have any experience with any of those, but there might be something that fits your needs.

You could try adding the __GL_THREADED_OPTIMIZATION=1 environment variable to the custom launch options, it improved performance and lessened bugyness for me.

You could also try to run the launcher with software rendering¹ by editing ~/.paradoxlauncher/launcher-v2.2024.1/Paradox Launcher (you might have to change the version). Try adding --disable-gpu in the last line, between --no-sandbox and "$@"

You could also try disabling gamemoderun. It hasn’t really improved performance in my experience, but has caused some bugs for me. It also muddies the logs.

¹Shamelessly stolen from https://www.protondb.com/app/394360#ju-PgaxbiU

Could you give a bit more information about the hardware and software setup?

• which GPU do your desktop and laptop have? (from what I could find online, the A285 has an iGPU from 2019. I really hope this is wrong)
• wayland or X11?
• hoi4 native or via proton?

I believe I had similar issues on my Nvidia GPU, but resizing the window was a complete fix in my case.

If the installer is small enough (<650MB I believe), you can upload it to virustotal.com to have it be scanned by ~65 antivirus programs

Ah, it looks like we have a small misunderstanding. I thought you were talking about uncompressed video, which is enormous. This is only used in HDMI cables for example. A 1080p60 uncompressed video is 2.98Gbit/s, or about 1.22 terabytes per hour.

A remux is “uncompressed” in the sense that it isn’t recompressed, or in this case transcoded. A remux is still compressed, just to a lesser degree than a transcode. This means the files are indeed larger, but the quality is also better than transcodes.

To clarify the article’s confusing statement: they claim that remuxes can reduce size by throwing away some audio streams, while keeping the original video. This is true, but the video itself hasn’t gotten any smaller: you are simply throwing away other information.