A controversial bill that would require all new cars to be fitted with AM radios looks set to become a law in the near future. Yesterday, Senator Edward Markey (D-Mass) revealed that the “AM Radio for Every Vehicle Act” now has the support of 60 US Senators, as well as 246 co-sponsors in the House of Representatives, making its passage an almost sure thing. Should that happen, the National Highway Traffic Safety Administration would be required to ensure that all new cars sold in the US had AM radios at no extra cost.

    • tal@lemmy.todayOP
      link
      fedilink
      English
      arrow-up
      26
      ·
      6 months ago

      You can improvise an AM radio receiver with stuff you have lying around your house.

      Not only that, it can be powered by the radio signal itself.

      https://en.wikipedia.org/wiki/Crystal_radio

      A crystal radio receiver, also called a crystal set, is a simple radio receiver, popular in the early days of radio. It uses only the power of the received radio signal to produce sound, needing no external power. It is named for its most important component, a crystal detector, originally made from a piece of crystalline mineral such as galena.[1] This component is now called a diode.

      Crystal radios are the simplest type of radio receiver[2] and can be made with a few inexpensive parts, such as a wire for an antenna, a coil of wire, a capacitor, a crystal detector, and earphones (because a crystal set has insufficient power for a loudspeaker).[3] However they are passive receivers, while other radios use an amplifier powered by current from a battery or wall outlet to make the radio signal louder. Thus, crystal sets produce rather weak sound and must be listened to with sensitive earphones, and can receive stations only within a limited range of the transmitter.[4]

    • captainlezbian@lemmy.world
      link
      fedilink
      arrow-up
      21
      ·
      6 months ago

      This is just making me think that there should be a fundamentals of modern technology class in high school somewhere between a shop and physics class. It’d be a nerd elective but by fuck am I that nerd

        • captainlezbian@lemmy.world
          link
          fedilink
          arrow-up
          7
          ·
          6 months ago

          Yeah as an engineer I think it would’ve been far more useful than the engineering class I took that was basically how to do autocad and measure things. And it would’ve been useful for everyone.

          There are two things at play here. 1) one of the primary purposes of the United States’s education policy is to produce engineers. This is an economic and military strategy. And 2) we live in a world where technology abounds and yet so few people understand it. A robot isn’t a magic person made of metal, it’s the manifestation of the laws of physics as applied for our own desires.

          Making a radio receiver and a telegraph and a record and telephone and a basic battery etc makes for more grounded adults. Show the teenagers the way the real world works, clever applications of natural phenomena

          • tal@lemmy.todayOP
            link
            fedilink
            English
            arrow-up
            2
            ·
            6 months ago

            A robot isn’t a magic person made of metal, it’s the manifestation of the laws of physics as applied for our own desires.

            I suppose if we discovered magic and understood its principles, it wouldn’t really be magic any more.

            Any sufficiently advanced technology is indistinguishable from magic.

            — Arthur C. Clarke

      • CancerMancer@sh.itjust.works
        link
        fedilink
        arrow-up
        1
        ·
        6 months ago

        Considering the growing importance of digital radio communication, Computer-Assisted Design, electronic repair, etc. I’d love to see this kind of thing.

    • Pretzilla@lemmy.world
      link
      fedilink
      arrow-up
      12
      ·
      6 months ago

      100% accurate, thanks for the clear write up. Please stick it up on Wikipedia if you can :)

      And I’ll add a bit about Clear Channel AM (unrelated to the billboard advertising company) - there were originally a handful of said stations that broadcast on a few AM band frequencies that are reserved just for them, so their broadcast range is impressive.

      One for example is WOR radio in Chicago.

      Fun factoid - you can see on very old AM radios those clear channel frequencies marked by a diamond or similar symbol on the dial.

      • Captain Aggravated@sh.itjust.works
        link
        fedilink
        English
        arrow-up
        25
        ·
        6 months ago

        Single Sideband is basically AM 2.0, so to talk about it in detail, we have to take a closer look at good old fashioned 19th century AM.

        The graphic above is from Wikipedia. The top graph, the “baseband” signal, is the audio, aka the signal coming out of the microphone. It’s vaguely what a human voice would look like on a specrograph.

        The second graph is what AM looks like. The spike in the middle is called the “carrier.” Let’s say you’re transmitting on 5 MHz with a 10 watt radio. When you push the talk button and then say nothing into the mic, you start broadcasting a 5 MHz wave with a power of 10 watts. A receiver tuned to 5 MHz will hear the background static go away, because you are transmitting a carrier wave that does not modulate much louder than the background noise, you are effectively holding the receiver’s speaker still. A signal coming in strong enough to do that we call “full quieting.”

        The carrier carries no information. Another way to look at these graphs is, picture the sine wave. You may have seen something like this before:

        That middle waveform represents AM, notice how there’s always some squiggles going through the middle, and it varies toward the top and bottom edges? That’s what the upper graphic is representing, that big center spike is always there for that reason.

        You may notice that the two lobes to either side are the same shape as the base band signal; or one of them is, the other is a mirror image. We call these sidebands. That’s actually where the audio is. In the second graphic, you can see how the top and bottom edges of the AM waveform resemble the baseband signal. Turns out, AM radio uses twice as much bandwidth and more than twice as much power to transmit the usable signal.

        So what if we built the transmitter to only transmit one of the two sidebands and suppress the carrier and the other sideband? The same audio information goes over the air, and we take up less room on the radio spectrum to do it. What’s more, since we’re transmitting less overall “stuff,” the radio’s power is more focused on the part we do transmit, so a single sideband transmission comes across as “louder” than an equivalent AM transmission.

        There are some cool upshots to how SSB works: the first is that the radio uses less power and overall stays cooler. AM (and FM) transmit with their full power all of the time, doesn’t matter if you whisper or scream into the microphone you’re putting whatever power your amplifier is set to out to the feed line. You might be transmitting silence, but it is very loud silence. SSB doesn’t do that; the louder you talk into the mic, the more power goes out the antenna. You aren’t constantly transmitting that carrier, so if your mic goes quiet, so does your antenna. Thus, your transmitter gear takes less power, runs cooler, and if you are on some consumable power source like batteries, you can transmit more effective power for longer.

        Even cooler than that is the lack of collisions. If you’ve played with radios much, even listening to music radio stations near the edge of their ranges where you can kind of hear both, you know they interfere with each other. Happens all the time with aviation radios, pilots will transmit on the same frequency at the same time and anyone else listening gets to listen to the psychedelic sounds of two carrier waves interfering with each other. On FM radios usually the louder signal “wins” and the other one just sounds like static or interference under it. SSB doesn’t do this.

        If two people transmit at the same time on the same frequency on SSB, a third person listening just hears two voices, just like if two people talked at the same time in a room. Hams hold contests to see who can make contact with the most people from the most places, and folks from somewhere rare will end up asking for contacts, everyone else says their callsigns at once like it’s the floor of the stock exchange, the one station will pick someone he heard to exchange details with, rinse and repeat. It’s 1950’s Discord.

        Hams also use this technique to send text back and forth extremely efficiently. If you tune your software defined radio to 14.070 MHz (or use one of several people make available online) you might hear what sounds like several strange warbling whistles that come and go. That is PSK31, a digital text mode designed to use an ordinary PC sound card as a modem, and an ordinary SSB transceiver to send the signals across the air. Using software like FLDigi, you can receive and transmit text over the air, and each text transmission is very narrow in bandwidth. Over a dozen can take place in the same space as a normal voice channel, you leave the radio tuned to 14.070 and choose which transmission to listen to by clicking on them in the waterfall, ie choosing what audio frequency to listen to, which only works using SSB because no carrier collisions.

        For all its advantages, there are some disadvantages. You cannot transmit “quiet” with SSB the way you can with AM or FM; so the background static, the “noise floor” is always there. Makes it not so nice for listening to music, which is why you basically only ever see it on communication radios. And it also requires a much more complicated transmitter and receiver while achieving the same or slightly worse audio quality than AM. You don’t see SSB used much in VHF and above because there’s so much room for activities/line of sight limits how far your signal goes so the efficiency advantages of SSB are less important, which is why we tend to use FM (or AM for old shit like airplanes) at wavelengths shorter than 6 meters or so.

    • Everythingispenguins@lemmy.world
      link
      fedilink
      arrow-up
      3
      ·
      6 months ago

      Very nice write up. I am curious, is the long wavelength Responsible for the rise and fall in audio quality depending on where you are. I have had this happen as I was driving, the sound quality seemed to pulse.

      Also I used to live right at the base of a tall mountain range there was a AM transmitter on the other side less than 100 miles away. During the daytime I could never receive it, at night it would bounce over the mountain and it was pretty clear.

      • Captain Aggravated@sh.itjust.works
        link
        fedilink
        English
        arrow-up
        6
        ·
        6 months ago

        I doubt the wavelength is a factor there; depending on the circumstances it could be anything from atmospheric waves to something in your car causing intermittent interference.

        The Earth’s ionosphere exists in several layers. During the day, solar radiation ionizes gas deeper into the ionosphere causing a layer that doesn’t usefully refract most radio waves; you can reach beyond the horizon on some of the higher HF bands, but down in the MF, you’ve basically got ground wave. At night, without the sun around to cook the atmosphere, that lower level dissipates, revealing a higher ever-present layer, and the geometry is right to refract signals for hundreds or even thousands of miles.

        Skywave propagation can be really fun to play with.

          • Captain Aggravated@sh.itjust.works
            link
            fedilink
            English
            arrow-up
            2
            ·
            6 months ago

            There likely was no “shielding” in a truck of that era, just simply the truck was made of metal as was the chassis of the radio, bolt 'em together and you’ve got a reasonable ground.

            But, I do know from experience that there are items on a pickup truck that can produce radio interference especially when worn. A worn distributor is a spark gap transmitter, as I learned when I installed a mobile radio in my S10. The audio on my radio got a lot better after a good service of the ignition system.